Latest news
Tips & GuidesRhino

Rhino 8 QuadRemesh and SubD: A Step-by-Step Guide to Controlled Topology

In Rhino 8, QuadRemesh creates regular quad meshes from surfaces, meshes, and SubD models, while ToSubD converts supported geometry to SubD. This guide explains how to choose options for your modeling goals.

An organic chair model showing both quad topology and a smooth surfaceAI image
Representative image, generated with AI.Image: 3dsınıfı / FCA AI

In brief

  1. QuadRemesh creates an editable quad mesh from an existing surface, mesh, or SubD.
  2. Target Edge Length depends on scale; Target Quad Count targets an approximate face count and is scale-independent.
  3. Guide Curves can direct edge flow or edge loops when projected onto the object.
  4. During ToSubD conversion, surface trims may be lost; non-manifold mesh edges and their associated faces are removed.

This guide is based on McNeel’s Rhino 8 documentation for QuadRemesh, ToSubD, and SubD. The goal is not simply to turn a model into more polygons, but to plan when to use a regular quad mesh, a SubD surface, or the original geometry. Since the effect of each option depends on the input geometry and desired result, assess the model’s scale, symmetry, and any sharp boundaries that need to be preserved before converting.

1. Choose a conversion goal

QuadRemesh creates a quad mesh with manageable topology from a surface, mesh, or SubD. According to the documentation, this mesh is designed for uses such as rendering, animation, CFD, FEA, and reverse engineering. If you need to convert the output to SubD, you can use the Convert to SubD option in QuadRemesh. This corresponds to the same conversion option as the ToSubD command.

First, clarify what you need: an approximate face count, a specific edge length, or a mesh that follows the surface shape more closely. In the Rhino 8 documentation, QuadRemesh is shown in the SubD / Mesh toolbar and under Edit Tools > Quad Remesh. You can also run it by command name and control the result using the settings below.

2. Set the edge length and face count

  1. Select the input object and run QuadRemesh. Choose your target metric with a view to how the result may vary at different model scales.

  2. If you want to set an edge length, use Target Edge Length. This value is scale-dependent: as the object’s scale increases, so does the resulting face count. If the target edge length is set too large relative to the object, remeshing may fail.

  3. If you want an approximate face count, use Target Quad Count. This setting is scale-independent; different-scale versions of the same input object can produce a similar face count.

  4. Check the result in Preview. The preview updates as you change the settings, and the dialog’s bottom section also calculates the average edge length and face count.

SettingSuggested valueEffect
Target Edge LengthSet according to model scaleScale-dependent; the face count increases as the scale increases. An excessively large target may cause the operation to fail.
Target Quad CountApproximate target face countTargets an approximate face count independent of scale.
Adaptive Size0Favors the fewest quads with more consistent sizing.
Adaptive Size100Preserves more detail and creates smaller faces in areas of high curvature.
Detect Hard EdgesOn or offWhen on, adds a hard-edge loop if the angle between adjacent faces is greater than 30 degrees.

There is no single ideal value for Adaptive Size. The documentation says that a value of 0 targets the fewest quads with consistent sizing; as the value increases, smaller faces appear in areas of higher curvature. Above 30, control over reducing the number of quads decreases. So preview both low and high values first, then compare face density in the model’s important areas.

3. Preserve boundaries, symmetry, and direction

For polysurface or extrusion inputs, the Use Surface Edges option controls how the boundaries of underlying surfaces are handled in the mesh. Off ignores these boundaries. Smart preserves them except when the algorithm considers them meaningless, and the documentation describes it as generally the best choice. Strict preserves all underlying surface boundaries. Check which boundaries you need to retain based on the model’s construction and desired topology.

If you know the appropriate center plane for a symmetrical object, you can enable symmetric remeshing along the X, Y, or Z axis; you can also select multiple axes. According to the documentation, this option is meaningful only when the object is truly symmetrical and the correct plane is selected.

Use Guide Curves to direct edge flow. The curves must be projected onto the input object; otherwise, they have no effect on the result. Curve Influence offers different strengths of guidance: Approximate has a weak influence on the general flow, Create Edge Ring directs edges that intersect the curves perpendicularly, and Create Edge Loop attempts to place edge loops along the curves. The documentation also notes that loops may not follow the curves exactly.

If sharp boundaries need to be preserved in the mesh, consider the Detect Hard Edges option. This setting adds a hard-edge loop when the angle between two adjacent faces is greater than 30 degrees. If the input mesh is irregular, you can turn the option off to avoid unwanted hard edges. For SubD output, SubD Creases and SubD corners transfer appropriate mesh edge and vertex properties to SubD.

4. Convert the mesh to SubD and verify the result

Use Convert to SubD to convert QuadRemesh’s quad output to SubD. When Interpolate SubD is on, mesh vertices are used as SubD points and the SubD stays on top of the quad mesh; the documentation notes that this approach is generally used for reverse engineering. When it is off, vertices are treated as SubD control polygon points, and the result may be slightly smaller or larger than the original shape.

Alternatively, the ToSubD command can convert mesh, extrusion, surface, and sub-surface objects. For meshes, the ControlPoints option treats vertices as SubD control points, while Location treats them as SubD points. Under UseSurface, you can also choose between ControlPoints and Location. The documentation identifies ControlPoints for Class A modeling work that requires separate SubDs to be combined into a single SubD; Location may target the best fit to the input NURBS surface and can create additional faces.

Before converting, account for these limitations: surface and sub-surface trims are lost in SubD; sub-surfaces in a polysurface are converted individually. Non-manifold mesh edges and their associated faces are removed. The Delete Input option controls whether the original geometry is deleted. So, especially if you need to keep editable source geometry, check this option and verify the conversion before proceeding.

Rhino SubD objects are Catmull-Clark subdivision surfaces; you can toggle between the flat box display and the smoothed display with the Tab key or the SubDDisplayToggle command. SubDs can be converted to NURBS or meshes, and exported to file formats that support mesh or NURBS. To increase mesh density, the SubDivide command applies Catmull-Clark subdivision steps to Mesh/SubD objects or selected faces.

Common mistakes

  • Setting Target Edge Length without accounting for model scale; an excessively large value can cause remeshing to fail.

  • Using Guide Curves without projecting them onto the object; they will have no effect on the result.

  • Enabling symmetry on a non-symmetrical model or using the wrong center plane.

  • Assuming that trims will be preserved when converting trimmed surfaces with ToSubD.

  • Failing to check for unwanted hard edges that may result from enabling Detect Hard Edges on an irregular input mesh.

Impact on architecture and visualization workflows

For work involving organic furniture, freeform cladding, or a mesh that needs to be converted into editable topology, QuadRemesh can be used to rebuild edge flow. If an architectural model needs to continue as dimensionally precise, manufacturable NURBS components, the ability to convert SubD to NURBS or mesh provides an option for the next stage. However, the documentation does not specify render times, performance gains, or hardware requirements, so the result should be tested separately in the project file and target application.

For an office workflow, the safest approach is to check whether the original geometry is retained and whether the output topology suits its intended purpose. In particular, the loss of trims, removal of non-manifold mesh components, and the possibility that SubD may differ slightly from the input shape should be reviewed before delivery. Rhino 8 documentation explains the features and their behavior; it does not provide a figure here for licensing terms, compatibility details with other software, or hardware requirements.

Sources

3 sources
D
docs.mcneel.comdocs.mcneel.com/rhino/8/help/en-us/commands/tosubd.htm
Summary
D
docs.mcneel.comdocs.mcneel.com/rhino/8/help/en-us/commands/quadremesh.htm
Summary
D
docs.mcneel.comdocs.mcneel.com/rhino/8/help/en-us/seealso/sak_subd.htm
Summary

Source texts are not republished; short quotes are marked, everything else is our own summary and commentary.

3dsınıfı’s take
3dEditor’s assessment

For architecture and visualization studios in Turkey, the practical value of QuadRemesh lies in its flexibility: it can turn a complex mesh into more manageable quad topology and, when needed, take that mesh on to SubD. Teams working with organic forms can adjust face density and edge flow to suit the project. However, the options documented in this guide do not guarantee the same result for every model; previewing and checking the output should be part of the process.

Before adding it to your workflow, decide whether the original geometry needs to be retained and account for the possibility that trims may be lost. The documentation does not specify hardware requirements, licensing costs, or performance gains, so it would be unwise to make assumptions on these points. Studios should also test export and delivery requirements for their other software using an actual project file.

Frequently asked questions

What is Rhino 8 QuadRemesh used for?

It creates a quad mesh with optimized topology from an existing surface, mesh, or SubD. The documentation lists rendering, animation, CFD, FEA, and reverse engineering as use cases.

What is the difference between Target Edge Length and Target Quad Count?

Target Edge Length depends on scale, and the face count increases as the object’s scale increases. Target Quad Count targets an approximate face count independent of scale.

Are trimmed surfaces preserved when converting to SubD with ToSubD in Rhino?

No. According to Rhino documentation, surface or sub-surface trims are not transferred to SubD; sub-surfaces within a polysurface are converted individually.

Comments and the forum are in Turkish.Join the discussion
+

Related news