In brief
- Make2D generates 2D drawing curves from model geometry based on the selected view.
- For a four-view output, use First angle projection for the European layout and Third angle projection for the US layout.
- Rhino PDF is a built-in printer option that supports saving layers to PDF files.
- In the Print window, scale, output color, linetype, and line weight can be adjusted separately.
This guide covers McNeel’s Rhino 8 documentation for the Make2D and Print commands as part of a workflow that runs from architectural technical drawings to printed sheets. Make2D creates 2D curves corresponding to a selected view of the model geometry, while Print lets you adjust scale, layout, and line properties to send a view or layout page to paper or PDF. The steps below are based on the options described in the Rhino 8 documentation.
1. Set the view and output layout for Make2D
Select the objects to include in the drawing, then open
Drafting › Make 2-D Drawing. Make2D places the curves it creates on the World Top plane. The Projection setting determines which view the output is based on.To use a single view, select
View. This creates a 2D drawing from the active view. By default, the output is positioned relative to the active view, with the view’s lower-left corner placed at the World origin.Consider
CPlaneto create a drawing from the plan view of the active viewport and place the curves on that viewport’s construction plane. If you need to align the new output with a drawing already created in the view, you can useRegister with previous; this option works only whenVieworCPlaneis selected under Projection.Choose a projection layout when you need a four-view output.
First angle projectionuses the European layout; view curves are created from the World Top, World Front, and World left views.Third angle projectionuses the US layout and the World Top, World Front, and World Right views. Both options use world coordinates for projection.
| Make2D option | Use | Effect |
|---|---|---|
View | Drawing from the active view | The output is created based on the active view. |
CPlane | Plan view of the active viewport | Curves are placed on the viewport’s construction plane. |
First angle projection | Four views, European layout | Uses the World Top, World Front, and World left views. |
Third angle projection | Four views, US layout | Uses the World Top, World Front, and World Right views. |
2. Check linetypes and layers
Make2D options affect the appearance and organization of the curves it creates. Tangent edges draws the tangent edges of polysurfaces. Hidden lines creates hidden lines on the specified Hidden layers. Scene silhouette displays object silhouettes with a heavier line weight, while Clipping plane intersections adds clipping plane intersection lines. Viewport rectangle can be used to show the viewport boundary as a rectangle in perspective views.
Use Object properties to take output properties from the source objects, or By output layers to define properties from the output layers. Group output lets you group curves according to their source objects. The Layer name field sets the main layer for the 2D drawing; different curve types are organized on sublayers. If you need to manage linetypes separately in the sheet layout, deciding on the layer structure and property options before generating the output can reduce the need for later edits.
3. Understand the limitations of overlapping and registered views
Register with previous attempts to match the previous output. Keeping a parallel view in the same position is easier; changes to a perspective view, such as panning, zooming, rotating, or resizing, can cause the match to fail. If no match is found, the current view is saved for subsequent use; an additional view record is also created for perspective viewports. The option can be turned off when you need to register a new parallel view.
Also note that Make2D does not automatically create intersection lines where objects intersect. If one object passes through another, create the intersection curve with the Intersect command and include it in Make2D. The seam of a single-surface cylinder may not be visible; a cylinder made from two half-cylinders may show two straight seams. Dimensions are also flattened. If silhouettes are very close to another curve, they may not appear on the correct layer; check critical drawings after output.
4. Set scale and PDF output with Print
Use
File › Printor theCtrl (CMD) + Pshortcut. Select the destination from the printer list.Rhino PDFsupports saving layers to PDF files. Available destination and paper-size options may vary by printer.Set the output scope: print the selected viewport or layout page, select
Extentsto include all objects in the model, or define a window area. If you select multiple layouts, navigate through the pages in the preview to check which layouts will be printed.Select a scale from the list in the
Scalefield, or set the relationship between paper units and model units. Use the relevant Margins and Position options to center the layout, define margins, or preserve the viewport aspect ratio. When a layout page is selected, the printer paper size changes to match the layout page size.Under
Output type,Vector outputprints lines, curves, and filled areas as vectors; by default, Rhino uses this method for objects it can print as vectors.Raster outputcreates a bitmap image but does not support saving layers to PDF. For color, choose the option that suits the output: Print color, Display color, or Black and white.
Linetypes can be printed using the current display properties in the view or the pattern in the definition file. Line weight options include a global multiplier, a default thickness, and model/page length settings. With Model lengths, line width changes according to zoom in the model view, while Page lengths uses a constant thickness on paper. Before printing, check the scale, line weight, color, and selected object scope together in the preview.
Common mistakes
Overlooking the difference between First angle and Third angle layouts when creating four views.
Changing a perspective view with
Register with previouson and assuming alignment with the previous drawing will be preserved.Expecting Make2D to automatically create intersection lines where objects intersect.
Using Raster output when a layered PDF is required; this output type does not support PDF layers.
Checking the scale and line weights only in the viewport, without reviewing the Print preview.
Impact on architecture and visualization workflows
Make2D is for architecture and interior design teams looking to create technical drawing curves from a model; Print is for users preparing these drawings as views or layouts for paper and PDF output. Deciding on the output layout, layer preferences, and scale from the outset makes them easier to control. The documentation does not provide information about hardware requirements, licensing costs, or compatibility with other software, so these points should be verified separately.
Sources
2 sourcesSource texts are not republished; short quotes are marked, everything else is our own summary and commentary.
Because these two commands connect the stages of creating drawings from a model and preparing the output, they offer offices a practical workflow, especially for recurring sheet work. Making decisions about views, layers, and scale early can reduce the workload of pre-delivery checks.
For teams in Turkey, the important point is to think from the outset about how the PDF will actually be used: if a layered file is required, choose Rhino PDF and vector output; for printing, review the scale, line weights, and preview separately. The documentation provides no information about hardware or licensing costs, so purchasing or workstation decisions should not be based on this guide.
Frequently asked questions
What is Rhino 8 Make2D used for?
It creates 2D drawing curves from model geometry based on the selected view. You can choose a single view or a four-view projection layout.
How do you create a layered PDF with Rhino Print?
Select Rhino PDF as the printer; this option supports saving layers to PDF files. The output type also matters, as Raster output does not support saving layers.
Does Make2D create intersection lines between objects?
Make2D does not create intersection lines where objects pass through one another. Create the curve with the `Intersect` command and include it in Make2D.



