In brief
- Solidify Modifier thickens a mesh surface and works as a modifier without changing the underlying geometry.
- Simple Mode is faster but may not work with some complex geometry; Complex Mode can handle more cases.
- If an object has non-uniform scale, thickness may vary across different directions; applying or clearing the scale can help.
- Changing modifier order affects the result; Apply removes the modifier and converts its result into geometry.
What will you learn in this guide?
Solidify Modifier is used in Blender to add depth and thickness to a mesh surface. You can continue adjusting its settings through the modifier while thickening walls, shells, or similar forms modeled as single surfaces. This guide explains how to add the modifier, assess Simple and Complex modes, use the Thickness and Offset settings, and handle open edges. We also look at how object scale, surface normals, and modifier stack order affect the result.
Modifiers are operations that affect the display and render result without directly changing an object’s underlying geometry. You can add multiple modifiers to an object, and their order affects the result. Once the settings are finalized, Apply converts the modifier’s result into geometry, but removes the modifier from the stack.
Requirements
You need a mesh object to add thickness to in Blender. The Blender Manual pages do not specify a required version number, account, or membership.
With the object selected, you can use the Add Modifier button near the top of the Modifiers tab in the Properties Editor. The manual also lists the Shift+A shortcut in the same tab as a way to add a modifier.
The source does not recommend an architectural measurement or specify a particular unit for the thickness value. Set the value according to the model and project requirements, then inspect the resulting surfaces.
The source also provides no hardware requirements. It notes that Complex Mode may be slower because of its additional calculation logic.
How to use Solidify, step by step
Select the mesh object. Make sure the surface to be thickened is part of a mesh object. Solidify works from the existing mesh surface; the geometry and the relationships between its surfaces can affect the result. It is especially useful to check junctions where more than one face connects to an edge.
Add Solidify Modifier. With the object selected, use the Add Modifier button in the Modifiers tab. The added modifier goes to the bottom of the stack and, by default, is evaluated last. If the stack contains multiple operations, the position of each modifier can change the result, so review the entire stack after adding Solidify.
Choose Simple or Complex mode. Simple is the default algorithm and extends the mesh geometry. It does not work with geometry where more than two faces connect to an edge. It may also fail to thicken a boundary when the normals of neighboring faces do not generally point in the same direction. Starting with Simple may therefore be suitable for more regular geometry.
Complex Mode handles a wider variety of geometry and aims to produce manifold output. The Blender Manual gives architectural wall layouts as an example of forms that Simple Mode may not be able to resolve. The manual recommends Simple unless there are special geometric cases; the additional calculation logic in Complex Mode can make the operation slower.
Set the Thickness and Offset values. Thickness determines how much thickness is added. Offset controls which side of the original surface the thickened geometry occupies, and to what extent; its value ranges from -1 to 1. A value of 0 centers the output around the original surface. Since the inside and outside direction depends on the surface normals, check the normals if the result appears on the wrong side.
Assess the thickness method in Complex Mode. Fixed keeps new vertices at a fixed distance from the old vertices. Even tries to account for sharp corners, but may not always work in areas where more than three faces meet. Constraints is an advanced option designed to distribute thickness more appropriately. According to the manual, an optimal solution is guaranteed for junctions of up to three faces; this does not mean every geometry will produce a flawless result.
Set how boundaries are handled. The Boundary setting determines how an open boundary is treated. None applies no additional boundary correction. Round adjusts the boundary of the opening inward. Flat makes the boundary of a planar opening flat; this setting is not described as an operation that closes the opening.
Rim – Fill creates edge loops and faces between the inner and outer surfaces along the surface edges. This option can be slow, so it can be disabled when not needed. Only Rim, which keeps only the rim geometry, behaves differently in Simple and Complex modes; inspect the resulting model if you use this setting.
Check the result and adjust if needed. View the model from different angles to check whether thickness is consistent at corners and junctions. The Even Thickness and High Quality Normals options in Simple Mode can improve quality in some cases, but may also increase calculation time. They do not guarantee perfectly uniform thickness for every topology. The source notes that results can vary, particularly at vertices where more than three faces meet.
Common mistakes
Overlooking non-uniform scale: Solidify calculates thickness using local vertex coordinates. If an object’s scale is not equal in different directions, thickness may also vary across different sides. The Blender Manual recommends applying or clearing the scale to correct this.
Using Simple Mode with every type of geometry: Simple may not work with geometry where more than two faces connect to an edge. The direction of surface normals also affects how boundaries are processed. If this happens, inspect the geometry and normals; try Complex Mode if necessary, bearing in mind that it may run more slowly.
Assuming Even Thickness guarantees an exact measurement: This option can help achieve more balanced thickness around sharp corners, but Solidify thickness is an approximation. Results may vary depending on topology, and exact wall thickness is not guaranteed.
Using Apply without checking modifier order: Blender evaluates modifiers from the top of the stack to the bottom. Changing their positions affects the result. Applying a modifier that is not at the top of the stack can produce an unwanted result by disregarding the operation order. Apply also removes the modifier and converts its output into geometry, so check the order and whether you still need to edit the result first.
Using Solidify in architectural and visualization workflows
Solidify can turn a single-surface wall or shell form into editable geometry with thickness. Being able to change thickness in the modifier settings while working on the form makes it easier to evaluate different values before finalizing the result. However, the source does not specify suitable wall thicknesses for a project, units of measurement, or compatibility with a particular render engine. Set the value according to the design requirements and verify the junctions and boundaries created in the model.
For a simple, regular surface, Simple Mode can be a faster starting point. Complex Mode can handle more cases with complex geometry, but calculation time may increase. For visualization teams, it is important to preserve modifier order and decide whether the result needs to remain editable before applying the modifier. Since the source provides no hardware requirements, it is not possible to recommend a specific system for performance expectations.
Next steps
Start with a simple test mesh and change the Thickness and Offset values to see how the geometry is positioned. Then compare Simple and Complex modes on the same model, paying particular attention to junctions and open boundaries. If thickness changes unexpectedly, check the object scale, surface normals, and modifier order separately. Finally, before using Apply, decide whether the result needs to be permanently converted into the underlying geometry.
Sources and license
This guide was adapted into Turkish based on the “Solidify Modifier” and “Introduction” pages in the Blender Manual. Both sources are published under the CC BY-SA 4.0 license.
Sources
2 sourcesSource texts are not republished; short quotes are marked, everything else is our own summary and commentary.
Solidify Modifier is an accessible tool for students and visualization teams who want to start with a single surface and create editable thickness in architectural modeling. For simple walls and shells, starting with Simple Mode and considering Complex Mode when the geometry requires it is a practical approach.
For offices in Turkey, seeing the result on screen may not be enough: complex geometry can take longer to calculate, and Even Thickness does not guarantee an exact measurement. The sources provide no hardware requirements or cost information, so no assumptions should be made about these. Before using Apply, it is also worth reviewing the modifier order and whether the model needs to remain editable.
Frequently asked questions
What does Blender Solidify Modifier do?
It adds depth and thickness to a mesh surface. Because it works as a modifier, you can adjust the result before applying it to the underlying geometry.
Should I choose Simple or Complex in Solidify Modifier?
Simple can be used with regular, simple geometry, but may not work with some face junctions. Complex can handle more geometric cases, but may be slower.
Why does Solidify Modifier produce different thickness in different directions?
Non-uniform object scale can cause thickness to vary across different sides. The Blender Manual recommends applying or clearing the scale.



